Reach Us +44 7456 035580
All submissions of the EM system will be redirected toOnline Manuscript Submission System. Authors are requested to submit articles directly toOnline Manuscript Submission Systemof respective journal.

Investigation of Sound Loss Potential of Natural Fibers and their Compositions

Malawade UA, Mahamuni KJ*, Dr. Madhavrao GJ and Dr. Virendra KB

Department of Mechanical Engineering, Jayawantrao Sawant College of Engineering, Hadapsar, Pune, Maharashtra, India

*Corresponding Author:
Ketan Jagadishrao Mahamuni
Department of Mechanical Engineering
Jayawantrao Sawant College of Engineering, Hadapsar
Pune-411028, Maharashtra, India
Tel:+91(020)26970886/87/88
E-mail: [email protected]

Received Date: 11/01/2017;Accepted Date:20/03/2017;Published Date: 27/03/2017

Visit for more related articles atResearch & Reviews: Journal of Engineering and Technology

Abstract

Natural fibers are porous in nature which is useful feature for sound absorption. Natural materials are ecofriendly and less harmful. Natural fibers have potential to play important role in acoustic treatments at various sensitive areas like hospitals, classroom, research laboratories, libraries, residential areas and offices. Experiments were conducted on natural fibers to understand its sound loss potential. The present paper also discusses method of sample preparation for the different compositions. Bagasse, Rice husk, Rice straw, Wood dust were tested to measure their sound loss potential. The test setup used for estimating the sound loss potential consisted of an emitter and receiver. Tests were conducted by measuring the sound level at receiver without any obstruction and readings were repeated by placing the sample in between. The difference of the two reading estimated the sound loss for that sample. The sound absorption coefficient for each case was estimated and compared with other similar materials reported in the literature. It was observed that sample made by combinations of rice husk, rice straw and wood dust gave considerable improvement in the performance. The present article discusses the sample preparation method, test setup used and results observed for different natural fibers. The present paper also gives results of compositions of different natural materials under investigation. Maximum sound absorption coefficient of the order of 0.29 was observed for Rice straw and Composition of Rice Straw and Wood dust sample.

Keywords

Natural fibers, Sound loss, Sound absorption coefficient, Bagasse, Rice husk, Rice straw, Wood dust

Introduction

Noise is one of the important sources ofenvironmental pollution. The increase in noise pollution is result of rapidindustrialization, vehicular traffic, trains, airplanes etc. which has adverse effect on human health. The technological development across the globe has many advantages for improving quality of life but it has certain side effects on human health, according to the recently estimated statistical data revealed that percentage of population was suffering from (53%) headaches, (36%) high blood pressure, (40%) anxiety, (36%) hearing disabilities, (15%)cardiovascular diseases, (67%) irritability and (61%) insomnia [1]。为了克服噪声speci的问题ally at sensitive areas such as hospitals, scientific laboratories, classrooms, residential areas and offices etc. acoustic treatment is essential so that the people occupying sensitive areas are not prone to pollution resulting due to sound emitted from various sources. Porous materials are widely used for noise control, which have high potential of sound absorption. These materials are categorized as porous foam or fibrous medium. Fibrous medium used for preparing sound absorbers are glass or rock wool which has high acoustic absorption properties. Foam is made from polyurethane. Foam has internal voids which traps the sound energy thus acts as good acoustic absorbing mediums [2]。This technique used for noise control is known as passive noise control method which uses materials like glass wool, polyurethane foam, asbestos etc [3]。These materials are expensive, flammable, non-biodegradable and harmful to society [4]。Hence it is important to investigate natural fibers to replace synthetic materials for sound absorption which have benefit of being easily available, low cost,recyclable,ecofriendly. Natural fibers have been receiving increased attention for applications in the field of acoustics. A variety of natural fibers are already being considered for commercial utilization in building and construction applications. Natural fibers are generally categorized as vegetable fibers, stalk orwoodfibers, bast or skin fibers, leaf fibers, seed fibers and fruit fibers [5]。Some of naturals fibers which has scope for applications are reeds, bagasse, cattail, corncob, cotton, date palm, durian, oil palm fiber, pineapple leaves, rice, sansevieria fiber, sunflower, straw bale etc. [6]。The theoretical methods are based on physical considerations ofsoundpropagation in materials, more complex independent variables such as tortuosity and porosity limits their use in practical applications [7]。There are several methods for measuring acoustic absorption that are normally carried out in impedance tubes with a loudspeaker and several microphones at low frequencies [8]。Some of the textile based sound absorbing materials have good acoustical absorbing properties and flexibility of applications. Several authors have successfully predicted absorption coefficients for the textile sound absorbing materials based on geometrical parameters [9]。Coconut coir fiber is widely used natural fiber for insulation and acoustic applications. Coconut coir fiber is prepared using combinations of latex and other additives with the coir fiber. Coir fiber with perforated plates on outer surface was utilized for enhancing sound absorption [10]。Use of Vegetable fiber like hemp has been reported for green building materials. Hemp concrete was made using different binders for utilizing the porosity which significantly enhanced the sound absorption capacity [11]。Sound absorption of tea-leaf-fiber was studied with sample thickness of 20 and 30 mm for frequency ranges of 500-3200 and 500-2400 hz respectively. Tea-leaf-fiber is good alternative for conventional materials due to its remarkable sound attenuation [12]。Coconut coir fiber has been used for construction of acoustic absorbing panel with help of perforated plates. These acoustic panels were tested for estimating acoustic absorption coefficient [13]。Acoustic absorbers were prepared utilizing sugarcane fibers as sustainable alternative over synthetic materials and the results shown were considerable [14]。

There are certain natural fibers which have scarcely been tested or reported. The present paper presents tests results such natural material. Sound absorption potentials are decided on the basis of noise reduction levels obtained using samples made by natural fibers and combinations of materials. A sound loss measurement test setup was used for measuring the sound loss potential of prepared samples.

Sample Preparation

Materials used in the present work are mainlyagricultural wasteswhich are easily available and ecofriendly.Rice husk, bagasse or cane fiber, and rice straw and wood fiber samples were prepared for investigation. Raw fibers were processed to make sample for testing of the materials. Following are the important steps employed in sample preparation:

Fiber Chopping Process

Raw micro porous materials from natural fiber were cut using chopping machine to prepare small uniform pieces of fiber filaments.

Fiber Extraction Process

The chopped materials were refined by separating the impurities present in it so that only natural raw material goes into sample preparation.

Sample Preparation

A mould of desired sample size (110 mm × 120 mm × 20 mm) was used for sample preparation to have constant sample thickness. Fiber filaments were blended with binder uniformly in the mould. Rubber synthetic R505 was used as adhesive. Prepared sample were kept under 90 kg weight for 48 hours and then solar dried for moisture removal for 72 hours.Figures 1-4gives the samples prepared from Wood Dust, Rice husk, Rice straw and Bagasse respectively.

engineering-and-technology-dust

Figure 1:Wood dust.

engineering-and-technology-husk

Figure 2:Rice husk.

engineering-and-technology-straw

Figure 3:Rice straw.

engineering-and-technology-bagasse

Figure 4:Bagasse.

Compositions of different materials were prepared by using adhesive to glue two individual samples. Compositions of natural fibers were also tested and results of the same are presented. Attention was paid during sample preparation to ensure samples of exactly same geometry, with same pressure applied and constant solar drying period. The constant pressure applied during the sample preparation ensured uniform internal structure in each case.

Experimental Test Setup

Test setup (Box size 800 mm × 150 mm × 140 mm and Internal cross section dimensions to accommodate sample 110 mm × 120 mm) used for experimentation was standard sound loss test setup as shown inFigure 5used for study of sound loss by different materials specimens prepared. Setup consists of sound source, sound receiver, closed wooden box and dB meter for measurement of sound at receiver end. The source and the receiver were placed 600 mm apart equally spaced from the center of the box and at an height of 70 mm. Source spectrum was varied in the frequency range of 125 Hz to 1500 Hz. Samples were tested with two different sound levels emitted from source (70 and 74 dB). Tests were conducted for 30 minutes for each sample at each sound level. Total testing time for each sample at two different sound levels was 1 hour. Three readings at a time interval of 10 minutes were recorded. Average reading for each source sound level has been reported to minimize error in measurement. To avoid flanking noise from surrounding interference in the measurement, the box was insulated using foam on inner walls and all the tests were conducted in the laboratory past midnight when all the other interfering noise are absent.

engineering-and-technology-photograph

Figure 5:Photograph of the test set up.

The sound proof box consists of two chambers containing a. Sound emitter and b. Sound receiver. Initial test is conducted inside the closed box without any barrier between source and receiver. Next the prepared sample is placed as a barrier and the box is closed again. The difference between the first and second reading (i.e., with and without barrier) gives the sound loss by using the prepared natural fiber. Following procedure elaborates the method employed for testing the specimens,

Procedure for Testing of Specimens (Refer图6):

engineering-and-technology-measuring

图6:Method employed for measuring the sound loss with samples placed in between source and emitter.

• Switch ON the dB meter and Sound Source to first sound level (70 dB).

•木箱和记录的把门关上the direct reading on dB meter without using any sound absorbing materialspecimenin between the source and receiver.

• Opening the box door and keeping the specimen as barrier between the source and receiver and closing the box.

• Recording the indirect reading while using specimen as barrier in between the source and receiver.

• Repeating the procedure for different sample specimens.

S- Sound source with variable Sound Level from70 dB-74 dB on either side of specimen

P- Base material used in combination having 20 mm thickness

Q- Different material as per combinations having 20 mm thickness

R- Sound Receiver / dB meter having range of 20 dB -120 dB for measuring the sound level

Experimental Tests Conducted on Samples

的测试进行了两种不同的声音levels viz. 70 and 74 dB. Tests were also conducted on composites by joining samples of two different materials but thickness in each case (single base material as well as composites of different materials) kept 40 mm constant for original sample as well as compositions to understand effect of pure natural fiber vis-à-vis its composites. Following tables and graphs give the results obtained from various tests carried out based on the procedure described above.

Initial Sound Level (dB)*-Readings obtained without any sound barrier in between sound source and receiver.

Final Sound Level (dB)**- Reading obtained by using sound barrier in between the sound source and receiver.

Table 1indicates maximum Sound loss of 20 dB and 18 dB for the two levels respectively during the tests conducted in case of test samples prepared from of composite of Rice Husk and Rice Straw.

Table 1.Sound loss results from tests conducted on rice husk based compositions.

Source Sound Level 1 Source Sound Level 2
Specimen Initial*
Sound Level (dB) (X)
Final**
Sound Level (dB) (Y)
吸收
Sound Level (dB) (X-Y)
Initial*
Sound Level (dB) (X)
Final**
Sound Level (dB) (Y)
吸收
Sound Level (dB) (X-Y)
Rice Husk 70 55 15 74 61 13
Rice Husk+RiceStraw 70 50 20 74 56 18
RiceHusk+Bagasse 70 54 16 74 59 15
Rice Husk+Wooddust 70 52 18 74 58 16

Table 2indicates maximum sound loss of 20 dB and 18 dB for the two sound levels respectively during the tests conducted in case of test samples prepared from composite of bagasse and rice straw.

Table 2.Sound loss results from tests conducted on bagasse based compositions

Source Sound Level 1 Source SoundLevel 2
Specimen Initial*
Sound Level (dB) (X)
Final**
Sound Level (dB) (Y)
吸收
Sound Level (dB) (X-Y)
Initial*
Sound Level (dB) (X)
Final**
Sound Level (dB) (Y)
吸收
Sound Level (dB) (X-Y)
Bagasse 70 54 16 74 58 16
Bagasse +RiceHusk 70 54 16 74 59 15
Bagasse+RiceStraw 70 50 20 74 56 18
Bagasse + Wood dust 70 51 19 74 56 18

Table 3indicates maximum sound loss of 22 dB and 20 dB for the two sound intensities respectively in case of test conducted on sample prepared from pure rice straw.

Table 3.Sound loss results from tests conducted on rice straw based compositions.

Source Sound Level 1 Source SoundLevel 2
Specimen Initial*
Sound Level (dB) (X)
Final**
Sound Level (dB) (Y)
吸收
Sound Level (dB) (X-Y)
Initial*
Sound Level (dB) (X)
Final**
Sound Level (dB) (Y)
吸收
Sound Level (dB) (X-Y)
Rice Straw 70 48 22 74 54 20
Rice Straw +Rice Husk 70 51 19 74 54 20
Rice Straw+Bagasse 70 53 17 74 55 19
Rice Straw +Wood dust 70 50 20 74 59 15

Table 4indicates maximum sound loss of 22 dB and 20 dB for the two sound levels respectively during the tests conducted in case of test conducted on samples prepared from composite of wood dust and rice straw.

Table 4.Sound loss results from tests conducted on wood dust based compositions.

Source Sound Level 1 Source SoundLevel 2
Specimen Initial*
Sound Level (dB) (X)
Final**
Sound Level (dB) (Y)
吸收
Sound Level (dB) (X-Y)
Initial*
Sound Level (dB) (X)
Final**
Sound Level (dB) (Y)
吸收
Sound Level (dB) (X-Y)
Wood dust 70 50 20 74 56 18
Wood dust+RiceHusk 70 50 20 74 56 18
Wood dust+Bagasse 70 50 20 74 54 20
Wood dust +RiceStraw 70 48 22 74 54 20

Results and Discussion

Graphs of investigation on different combinations of materials and their Sound loss levels at two distinct sound levels emitted (70 and 74 dB) are plotted below for the sound level measure at the receiver with various tests samples and there composites prepared and placed as barrier between the sound source and emitter.

engineering-and-technology-specimen

图7:For source sound level 1 of 70 dB (40 mm thickness specimen in each case).

A- Rice husk with 40 mm thickness by combinations of two samples of 20 mm thickness

B-Bagasse有40 mm thickness by combinations of two samples of 20 mm thickness.

C- Combination of Rice straw and Rice husk samples of 20 mm thickness each (total 40 mm)

D- Wood dust with 40 mm thickness by combinations of two samples of 20 mm thickness.

E- Combination of Bagasse and Rice Straw samples of 20 mm thickness each (total 40 mm)

F- Rice Straw with 40 mm thickness by combinations of two samples of 20 mm thickness.

G- Combination of wood dust and Rice Straw samples of 20 mm thickness each (total 40 mm).

engineering-and-technology-sound

Figure 8:For source sound level 2 of 74 dB (40 mm thickness specimen in each case).

A- Rice husk with 40 mm thickness by combinations of two samples of 20 mm thickness

B- Bagasse with 40 mm thickness by combinations of two samples of 20 mm thickness

C- Wood dust with 40 mm thickness by combinations of two samples of 20 mm thickness.

D- Combination of Bagasse and Rice Straw samples of 20 mm thickness each (total 40 mm)

E- Combination of Rice straw and Rice husk samples of 20 mm thickness each (total 40 mm)

F- Rice Straw with 40 mm thickness by combinations of two samples of 20 mm thickness.

G- Combination of wood dust and Rice Straw samples of 20 mm thickness each (total 40 mm).

图7shows the sound level decrements for different combinations form 55 dB to 48 dB with reference to direct reading without barrier for sound level of 70 dB. SimilarlyFigure 8shows decrement from 61dB to 54dB with reference to direct sound level of 74 dB.

Tables 5 and 6give the sound absorption coefficient from literature and from the current tests conducted respectively.

Table 5.Acoustic absorption coefficient from literature for natural and synthetic materials.

Material (Specimen) Thickness (mm) Sound Absorption Coefficient(avg) Note
Glass Fibers wool[2] 25 0.23 Specimen tested for specific density
Date Palm Fiber[3] 10-30 0.13 Specimen tested for different compression ratio
Jute CompositeMaterial[4] 25 0.53 Latex jute composites are usedfor test
Recycled PET[6] 10 0.09 Recycled polyethylene fiberwas tested as alternative
Double layer woodFiber[7] 25 0.25 Multiple layer of wood fiberwere used for better results
Coconut Coir Fiber [13] 20 0.28 Materials used with perforatedplates
Sugarcane WastedFiber[14] 15 0.21 Measured for fiber and bindercomposition of 70:30

Note- Sound absorption coefficients mentioned in the table above are average values for the low frequency range of the source i.e., 125 Hz to 1500 Hz.

Table 6.Acoustic absorption coefficients for different test specimens and material combinations obtained from tests conducted in present

Specimen Sample Thickness (mm) Sound Absorption Coefficient (avg)
SINGLE MATERIAL
Rice Husk 20 0.19
Bagasse 20 0.22
Rice Straw 20 0.29
Wood Dust 20 0.26
MATERIAL COMBINATIONS
Rice Husk + Rice Straw 40 0.26
Rice Husk + Bagasse 40 0.22
Rice Husk + Wood Dust 40 0.24
Bagasse + Rice Husk 40 0.22
Bagasse + Rice Straw 40 0.26
Bagasse + Wood Dust 40 0.26
Rice Straw + Rice Husk 40 0.27
Rice Straw + Bagasse 40 0.25
Rice Straw + Wood Dust 40 0.24
Wood Dust + Rice Husk 40 0.26
Wood Dust + Bagasse 40 0.28
Wood Dust + Rice Straw 40 0.29

Note- Sound absorption coefficients mentioned in the table above are average values for the low frequency range of the source i.e., 125 Hz to 1500 Hz by taking average of the two sound levels.

The sound absorption coefficients for materials tested in the present work can be compared with natural fibers reported in literature for frequency range between 125 Hz to 1500 Hz. Above results are in the range of 2 to 15% as compared to the reference values in literature.

Test Specimen

Figure 9shows sound absorption coefficient for rice straw and composition of rice straw and wood dust were maximum and around 0.29.

engineering-and-technology-coefficient

Figure 9:Sound absorption coefficient for rice straw and composition of rice straw and wood dust were maximum and around 0.29.

Conclusion

Sound absorption coefficients obtained for different materials and material compositions in this work are comparable with the values referred for different materials from literature. Specimens used in present work give remarkable sound absorption coefficients especially rice straw samples and sample made from combinations of wood dust and rice straw for the frequency range of 125 Hz to 1500 Hz. Maximum coefficient of sound absorption was for Rice straw and Composition of Rice straw and Wood dust which was estimated to be 0.29.

References

Global Tech Summit